Liber0 schreef:Vandaag mijn laptopje aangesloten op de V40 T4 1997
gaf aan 1998??
service licht gereset fouten... bij terug melding
ff starten...toen was het vevelende lichtje wel uit
met een stekkertje van 10 euro op de USB van je laptop..dus toch mogelijk met wat goede software
laptop draait op windows 7 = Ausus EEEPC 901
iemand ervaring met zulk soort FCR software?? graag wat tips om zonder foutmeldingen te werken
Wel heb ik volgens onderhoudschema olie filters en tandriem gewisseld
Afgelopen weekend met mijn Vol FCR en de oude laptop wat foutcodes weten te resetten.
Bij Cor ging veel goed, hij had wat foutcodes die ik niet begreep (vastgelegd op foto), bij Wouter ging ook alles goed alleen bij Nick werkte het niet. Beetje raar aangezien ze allemaal voorzien waren van dezelde ECU en de bouwjaren varieerde van 1997 tot 1999.
Bij mij werkt VOl FCR trouwens perfect op mijn V40 T4 uit 1998.
DirkT4 schreef:Afgelopen weekend met mijn Vol FCR en de oude laptop wat foutcodes weten te resetten.
Bij Cor ging veel goed, hij had wat foutcodes die ik niet begreep (vastgelegd op foto), bij Wouter ging ook alles goed alleen bij Nick werkte het niet. Beetje raar aangezien ze allemaal voorzien waren van dezelde ECU en de bouwjaren varieerde van 1997 tot 1999.
Bij mij werkt VOl FCR trouwens perfect op mijn V40 T4 uit 1998.
Draait die laptop dan op win xp of win7 of win98???
Bij mij werkt het niet op windows 7......
V40 T4 1997 Exclusive Line 332 black metallic Art Leather hagel nieuw 4204T blok 14T turbo
V3lv3T schreef:DirkT4 is net langs geweest en ook wij hebben het geprobeerd, maar niet gelukt.
Hij pakt de COM1 gewoon niet.
Als ik de boel aansluit, installeert vista gewoon zelf de drivers, en verschijnt het ook bij apparaatbeheer als USB Serial device (of iets dergelijks)
Maar in welke poort ik de kabel ook doe, hij geeft steeds COM3 t/m COM7 aan als "in use" maar COM1 wil niet.
Als het in apparaatbeheer op COM1 staat, pakt het programmatje hem nogsteeds niet...
Probeer anders dit 's: http://www.ftdichip.com/Drivers/VCP.htm "Virtual COM port (VCP) drivers cause the USB device to appear as an additional COM port available to the PC. Application software can access the USB device in the same way as it would access a standard COM port."
PS: Kijk eerst in 't boekje van je Volvo of je EMS2000 hebt. Dat is 'ODB2-geschikt'. Phase I Turbo en Phase II/III kunnen in principe alleen van FCR gebruik maken.
For technical support:
Tel 0870 7543 827 Mon-Fri 09:00-18:00 (GMT) or Fax 0870 7543 829 Anytime.
e-mail volfcr@onboarddiagnostics.co.uk
This program is designed to read & reset fault codes on Volvo (TM) cars.
The program has no connection with the Volvo Car Corporation.
The program will only work on Comm Port 1.
Some S/V 40 engine functions have not been implemented and are disabled.
No liability can be accepted for use of the program or the information presented.
You may wish to print information from the program, the easiest way to do this is to press the Alt + Print Screen keys to take a snap shot of the screen then press 'Go Back' to stop comms and finally paste the screen into a program such as Wordpad, save the result and print / e-mail as required.
-Scroll Down for more-
On ‘96/’97 850 cars with the 16 way ‘OBDII’ socket, and some other models, some of the control modules use ‘flash’ codes, this program is not designed to work with these modules.
The controls for these have been coloured yellow in the program.
THE USE OF THE FOLLOWING INFORMATION IS ENTIRELY AT THE USERS RISK
To retrieve the flash codes the following procedure can be adopted:
Connect an LED, with the correct polarity, in series with a 1k8 ohm resistor, between pin 16 (+) and pin X, where X is the pin corresponding with the module to be read. Connect a push to make switch between pin X and pins 4 or 5 (-).
The circuit can then be used in the same way as the pre ’96 diagnostic sockets, situated in the engine compartment.
For
Motronic 4.3 or Fenix 5.2, X = 3.
ECC , X = 6, Timer Type 4, X = 9.
Cruise Control, X = 13; 900 & S/V 90 ABS, X = 12 .
Ga binnenkort een interface (in bestelling) proberen met wat software (Vol-FCR of andere OBD-ware) gekoppeld aan een laptopje.. Vol-FCR heb ik onder Vista en Win7 in ieder geval al kunnen installeren.
To be continued.